S_DefocusPrism Defocuses the color channels of the source clip into rings of different widths. In the Sapphire Blur+Sharpen effects submenu. Inputs: Source:  The clip to be processed.

Parameters:

Defocus Width:   Default: 0.022,  Range: 0 or greater.
The width of the defocus. This parameter can be adjusted using the Defocus Width Widget.

Rel Height:   Default: 1,  Range: 0.01 or greater.
The relative height of the iris shape. If it is not 1, circles become ellipses, etc.

Shape:   Popup menu,  Default: Circle.
Determines the shape of the simulated camera iris.

Circle:  round.

3 sides:  triangle.

4 sides:  square.

5 sides:  pentagon.

6 sides:  hexagon.

7 sides:  etc.

Show Shape:   Check-box,  Default: off.
Show the iris shape instead of the defocused image.

Roundness:   Default: 0,  Range: any.
Modifies the shape of the simulated camera iris. A value of 1 produces a circle; 0 gives a flat-sided polygon with a number of sides given by the Shape parameter. Less than 0 causes the sides to squeeze inward giving a star shape, while a value greater than 1 causes the corners to squeeze inward, giving a flowery shape. Has no effect if the Shape is set to Circle.

Rotate:   Default: 0,  Range: any.
Rotates the iris shape.

Bokeh:   Default: 0,  Range: any.
Softens the outer edge of the iris shape, which gives a softer look to the defocused highlights. A negative value darkens the center of the iris shape, producing a ring-like defocus shape.

Lens Noise:   Default: 0,  Range: 0 or greater.
Increase to add noise to the iris shape, dirtying up the defocus a little. Can make the result more realistic. Turn up past 1 for a more stylistic result.

Noise Freq:   Default: 40,  Range: 0.01 or greater.
The frequency of the added noise. Ignored if Lens Noise is zero.

Noise Freq Rel X:   Default: 1,  Range: 0.01 or greater.
The relative horizontal frequency of the added iris noise. Increase to stretch it vertically or decrease to stretch it horizontally.

Noise Seed:   Default: 0.123,  Range: 0 or greater.
The seed value for the added noise. To make the noise appear different on each frame, animate this to be different on each frame. The actual value doesn't matter; only that it's different.

Gauss Blur:   Default: 0,  Range: 0 or greater.
If positive, a gaussian blur is also applied which smooths out the edges of the shapes. This might also darken the highlights because Gamma is not considered in the gaussian blur.

Use Gamma:   Default: 1,  Range: 0.1 or greater.
Values above 1 cause highlights in the source clip to keep their brightness after the defocus is applied.

Boost Highlights:   Default: 0,  Range: 0 or greater.
The amount to increase the luma of the highlights in the source clip. Increase this parameter to blow out the highlights without affecting the darks or mid-tones.

Hilight Threshold:   Default: 0.9,  Range: 0 to 1.
The minimum luma value for highlights. Pixels brighter than this will be brightened according to the Boost Highlights parameter.

Brightness:   Default: 1,  Range: 0 or greater.
Scales the brightness of the result.

Offset Darks:   Default: 0,  Range: -8 to 2.
Adds this gray value to the darker regions of the result. This can be negative to increase contrast.

Scale Color:   Default rgb: [1 1 1].
Scales the color of the result. For example, if it is yellow [1 1 0], the blue of the result will be 0.

Chroma Sep:   Default: 0.3,  Range: -1 to 1.
The amount of separation between the three color channel rings.

Chroma Ringthick:   Default: 0.3,  Range: 0.01 or greater.
The thickness of each of the three color channel rings.

Mix With Source:   Default: 0,  Range: 0 to 1.
Interpolates between the defocused result and the original source. Set this to 1 for the original source.

Edge Mode:   Popup menu,  Default: Reflect.
Determines the behavior when accessing areas outside the source image.

Transparent:  Areas outside the source image are treated as transparent, which can produce transparency around the edges of the image. Select this for fastest rendering.

Repeat:  Repeats the last pixel outside the border of the image.

Reflect:  Reflects the image outside the border.

Show Defocus Width: Check-box, Default: on.
Turns on or off the screen user interface for adjusting the Defocus Width parameter.

See Also:

RackDefocus

RackDfComp Blur BlurChannels BlurChroma WarpChroma Convolve

Sapphire Plug-ins Introduction

© 2009, GenArts, Inc. All rights reserved.